Tomb's 65 Comet Build

The Era of The Square Body Racing Comets
popscomet
Posts: 9398
Joined: Sat Jan 01, 2011 10:19 pm
Location: Jacksonville, Arkansas

Re: Tomb's 65 Comet Build

Post by popscomet »

popscomet wrote:By all means,,all of my trucks and cars have a clutch,,,except my very low mileage 94 F150,,and sometimes I just drive it to stay away from the clutch...thanks POP
forgot,,,my 1977 bronco has a AT....
Image
pop/glenda

lavron
Site Admin
Posts: 4442
Joined: Sat Nov 01, 2003 8:17 am
Location: Missouri, Ozarks way North
Contact:

Re: Tomb's 65 Comet Build

Post by lavron »

tomb22 wrote:This time I moved the the radiator as far forward as I could get it
Do you have any idea how much space you gained in front of the motor over the old setup? I intend to cut the core support like you did.

Right now with my 250-6 I think the stock radiator would fit and maybe even a belt driven fan (don't know never mocked the fan in there) but would like more room because I am adding the Contour fans and shroud (I got them the other day, they are really thin) of course I am in no position to mock anything up at the moment :roll: I think I will be ok because my water pump pulley is the nearest to the radiator and should fall between the dual Contour fans.

See Ya,
Mike
64 Comet 202 Sedan, My first car, I have owned it since 1979!
Image
Performance rebuild on a BUDGET - Installed; 250-6, T-5, 8.8 LSD, MII, Air Ride - Whatever I do it will be awesome!

tomb22
Posts: 536
Joined: Thu Jan 28, 2016 7:11 pm

Re: Tomb's 65 Comet Build

Post by tomb22 »

lavron wrote:
tomb22 wrote:This time I moved the the radiator as far forward as I could get it
Do you have any idea how much space you gained in front of the motor over the old setup? I intend to cut the core support like you did.

Right now with my 250-6 I think the stock radiator would fit and maybe even a belt driven fan (don't know never mocked the fan in there) but would like more room because I am adding the Contour fans and shroud (I got them the other day, they are really thin) of course I am in no position to mock anything up at the moment :roll: I think I will be ok because my water pump pulley is the nearest to the radiator and should fall between the dual Contour fans.

See Ya,
Mike
Here is a picture Mike of the water pump pulley between the 2 fans like your thinking. This set up gained me 3/8" from my old set up.

Image

tom
Image
tomb's 65

tomb22
Posts: 536
Joined: Thu Jan 28, 2016 7:11 pm

Re: Tomb's 65 Comet Build

Post by tomb22 »

I finally got to putting it back together. First I installed the angle iron bracket which fits behind the radiator mount.

Image

The picture doesn't show it very well. I then mounted the radiator to the angle iron thru the radiator mount with the bottom as close to the radiator mount as possible without touching the mount. The top of the radiator slants back a little so that the cap is accessible. I still had to cut out the top a little.

Image

Then added the shroud and fans.

Image

So far it all seems to be working out
Thanks for looking
tom
Image
tomb's 65

lavron
Site Admin
Posts: 4442
Joined: Sat Nov 01, 2003 8:17 am
Location: Missouri, Ozarks way North
Contact:

Re: Tomb's 65 Comet Build

Post by lavron »

tomb22 wrote:This set up gained me 3/8" from my old set up.
I guess you can't complain about that, bigger radiator and a bit more room.

Thanks for sharing the picts they help a lot.

As soon as I am flipped back upright and have wheels again I may mock my engine in again just to make sure I haven't caused any issues adding stuff and I can get the core support modded and my radiator/fans mocked in. I wish my motor was done so I could just slap it in and drive :roll: :P

See Ya,
Mike
64 Comet 202 Sedan, My first car, I have owned it since 1979!
Image
Performance rebuild on a BUDGET - Installed; 250-6, T-5, 8.8 LSD, MII, Air Ride - Whatever I do it will be awesome!

tomb22
Posts: 536
Joined: Thu Jan 28, 2016 7:11 pm

Re: Tomb's 65 Comet Build

Post by tomb22 »

I finally got the AC condenser and a new transmission cooler installed. The front looks a lot more cleaner than it used too.

Image

I need a new AC line made with a different fitting than I had to finish it. I probably won't get that done now until this virus thing is over. We go on lock down tomorrow at 8 am.
Thanks for looking
tom
Image
tomb's 65

tomb22
Posts: 536
Joined: Thu Jan 28, 2016 7:11 pm

Re: Tomb's 65 Comet Build

Post by tomb22 »

It's been a while, but I did get the car all back together. Got the AC recharged and have been driving it. The new Granada spindles have shorter tie rod arms which have made the turning radius smaller which works better with my rack and pinion. I got the alignment set up with .125- camber and 4.125+ caster. The toe in is 1/8" and the car drives really well.
For a winter project I'm buying this coil over kit for the front. It will let me adjust the ride height. I want to raise the front 1" so the headers won't get hung up on the trailer when I take it to the track, If I do. I can also adjust the ride for a nice smooth cruise. Right now the front is a little stiff compared to the back. The T on the shock is also bearing-ed.

Image

It's fun to watch everybody looking at it wondering what it is. :D
tom
Image
tomb's 65

Post Reply