trick flow FE dual quad intake

390 & up cid Monster Motors
Post Reply
User avatar
loman
Posts: 1297
Joined: Sat Dec 28, 2013 9:03 am
Location: Missouri

trick flow FE dual quad intake

Post by loman »

I bought the trick flow FE heads for my 390 project. One of the reasons I chose them was because the trick flow salesman I was talking to about the heads said they were working on a dual quad intake for 2019. Here is a link to it at the SEMA show.

https://www.youtube.com/watch?v=F2ZH5A_qjpg
Image

Lip Ripper
Posts: 1870
Joined: Wed Jun 06, 2012 6:47 am
Location: Lake Placid, Florida

Re: trick flow FE dual quad intake

Post by Lip Ripper »

Can't go wrong with TFS. And are you stroking this engine?
66 Cyclone GT; 245/60R15's on 15x8's and 215/70R15's on 15x7 Magnum's.
There's nothing like the sound of a pushrod V8 singing at the top of her lung's.

User avatar
loman
Posts: 1297
Joined: Sat Dec 28, 2013 9:03 am
Location: Missouri

Re: trick flow FE dual quad intake

Post by loman »

It will not be stroked for now. We will run the single 4bbl intake until we get the car pretty well sorted out. Then when we are ready we will buy the 2 4bbl setup for NSS. At least that is the plan for now. Subject to change daily. :lol:
Image

User avatar
fryedaddy
Posts: 711
Joined: Mon Nov 03, 2014 12:40 am
Location: east tn

Re: trick flow FE dual quad intake

Post by fryedaddy »

i hear folks are getting good power from the trick flow heads but dont forget to address the rockerarm pads. you have to mill .250 off of the rocker pads to get the geometry right on tfs heads.for some reason trick flow rocker stand pads are .250 taller than stock.i dont know why they did that,but it has to be addressed.
Last edited by fryedaddy on Sun Mar 03, 2019 10:50 am, edited 1 time in total.
fryedaddy
Image1966 caliente,428 4 speed,4.11 gears,nitrous,parachute

User avatar
loman
Posts: 1297
Joined: Sat Dec 28, 2013 9:03 am
Location: Missouri

Re: trick flow FE dual quad intake

Post by loman »

I emailed Trick Flow a week or so ago and finally received a response yesterday on the availability of the intake. The email stated it will be available in the summer.
Image

lazer
Posts: 38
Joined: Wed Oct 07, 2020 4:26 pm

Re: trick flow FE dual quad intake

Post by lazer »

fryedaddy wrote:
Sun Dec 30, 2018 4:53 pm
i hear folks are getting good power from the trick flow heads but dont forget to address the rockerarm pads. you have to mill .250 off of the rocker pads to get the geometry right on tfs heads.for some reason trick flow rocker stand pads are .250 taller than stock.i dont know why they did that,but it has to be addressed.
You don't have to mill the heads if you use Harland Sharp rockers. The head are set up for them.

User avatar
fryedaddy
Posts: 711
Joined: Mon Nov 03, 2014 12:40 am
Location: east tn

Re: trick flow FE dual quad intake

Post by fryedaddy »

thats what i bought hs rockers 1000 bucks,harland sharp or mill,your choice.
fryedaddy
Image1966 caliente,428 4 speed,4.11 gears,nitrous,parachute

Post Reply